Pr(H3BNMe2BH3)3 and Pr(thd)3 as Volatile Carriers for Actinium-225. Deposition of Actinium-Doped Praseodymium Boride Thin Films for Potential Use in Brachytherapy.

Here we show that the praseodymium N,N-dimethylaminodiboranate complex Pr(H3BNMe2BH3)3 and the 2,2,6,6-tetramethylheptane-3,5-dionate complex Pr(thd)3 can serve as volatile carriers for 225Ac. The actinium coordination complexes Ac(H3BNMe2BH3)3 and Ac(thd)3 are the likely species subliming with the carrier material. A sample of 225Ac-doped Pr(H3BNMe2BH3)3 was used to deposit amorphous 225Ac-doped praseodymium boride films on glass and Si(100) at 300 °C. The α emission spectra of the refractory films are well-resolved, suggesting that they could be used as radioactive implants for brachytherapy and related treatments.

Novel rapid oxidizing fusion method to determine Polonium-210 in air filters.

A rapid method for the determination of polonium-210 in air filters has been developed for use following a radiological event and for routine environmental monitoring. Air filter samples, including cellulose and glass fiber, are fused with a sodium or potassium nitrate/sodium hydroxide flux material. The alkaline matrix minimizes polonium volatility during sample digestion steps, while efficiently dissolving the air filter and inorganic matter implanted on the filter. The addition of nitrate to the flux destroys organic material which can decrease Polonium recovery during precipitation, extraction and source preparation steps. Polonium is concentrated and separated from the sample matrix using an iron hydroxide precipitation and extraction chromatography with DGA Resin. Polonium-210 is subsequently measured by alpha spectrometry following rapid microprecipitation with bismuth phosphate. The new method employs extraction chromatographic purification to remove alpha emitting interferences and sample matrix constituents which can interfere with 210Po measurements using alpha spectrometry. The novel blend of sodium hydroxide and alkali metal nitrate digests the air filters quickly and effectively.

Rapid method to determine Polonium-210 in urban matrices.

A rapid method for the determination of polonium-210 in urban matrices has been developed that can be used following a radiological event. Samples such as concrete, soil and granite are fused with sodium hydroxide to minimize polonium volatility during sample digestion and to achieve complete sample dissolution. Complete dissolution of samples is important to ensure method ruggedness. Polonium is concentrated and separated from the sample matrix using an iron hydroxide precipitation and extraction chromatography and subsequently measured by alpha spectrometry following microprecipitation with bismuth phosphate. The chromatographic separation removes alpha emitting interferences and matrix constituents which can adversely impact the measurement via alpha spectrometry.

Rapid method to determine plutonium, neptunium, americium and curium in granite samples.

A fast method for determination of plutonium, neptunium, americium and curium isotopes in granite has been developed for use following a radiological event. Granite samples are fused with sodium hydroxide to achieve complete dissolution, critical if refractory particles are present. Rapid precipitation steps are utilized to preconcentrate the actinide isotopes and remove sample matrix interferences. Plutonium, neptunium, and americium/curium are separated using innovative extraction chromatography and measured by alpha spectrometry. The sample preparation time is less than four hours.

Selective separation of radium and actinium from bulk thorium target material on strong acid cation exchange resin from sulfate media.

This work presents a complete scheme for the selective separation of actinium and radium isotopes from bulk 232Th target material, in a process that may be applied in a separation scheme for the production of 225Ac by proton spallation on thorium. Thorium metal is dissolved in sulfuric acid with small amounts of HF. Actinium and radium are retained on cation exchange resin from the sulfate medium, while neutral and anionic thorium sulfate complexes are rejected. Following rinsing steps to remove residual thorium, actinium and radium are recovered from the cation exchange resin using 5 M HNO3. Further separations of actinium via extraction chromatography with UTEVA and DGA resins yield actinium in >92% yield, while providing additional decontamination from thorium and other spallation byproducts. The radium fraction can be further processed following ingrowth of 225Ac from 225Ra to produce additional 225Ac free from any potential 227Ac impurity.

An europium(III) diglycolamide complex: insights into the coordination chemistry of lanthanides in solvent extraction.

The synthesis, stoichiometry, and structural characterization of a homoleptic, cationic europium(III) complex with three neutral tetraalkyldiglycolamide ligands are reported. The tri(bismuth tetrachloride)tris(N,N,N',N'-tetra-n-octyldiglycolamide)Eu salt, [Eu(TODGA)3][(BiCl4)3] obtained from methanol was examined by Eu L3-edge X-ray absorption spectroscopy (XAS) to reveal an inner-sphere coordination of Eu(3+) that arises from 9 O atoms and two next-nearest coordination spheres that arise from 6 carbon atoms each. A structural model is proposed in which each TODGA ligand with its O=Ca-Cb-O-Cb-Ca=O backbone acts as a tridentate O donor, where the two carbonyl O atoms and the one ether O atom bond to Eu(3+). Given the structural rigidity of the tridentate coordination motif in [Eu(TODGA)3](3+) with six 5-membered chelate rings, the six Eu-Ca and six Eu-Cb interactions are readily resolved in the EXAFS (extended X-ray absorption fine structure) spectrum. The three charge balancing [BiCl4](-) anions are beyond the cationic [Eu(TODGA)3](3+) cluster in an outer sphere environment that is too distant to be detected by XAS. Despite their sizeable length and propensity for entanglement, the four n-octyl groups of each TODGA (for a total of twelve) do not perturb the Eu(3+) coordination environment over that seen from previously reported single-crystal structures of tripositive lanthanide (Ln(3+)) complexes with tetraalkyldiglycolamide ligands (of the same 1:3 metal-to-ligand ratio stoichiometry) but having shorter i-propyl and i-butyl groups. The present results set the foundation for understanding advanced solvent extraction processes for the separation of the minor, tripositive actinides (Am, Cm) from the Ln(3+) ions in terms of the local structure of Eu(3+) in a solid state coordination complex with TODGA.

Rapid methods for the isolation of actinides Sr, Tc and Po from raw urine.

Rapid methods for the isolation and analysis of individual actinides (Th, U, Pu, Am/Cm) and Sr, Tc and Po from small volumes of raw urine have been developed. The methods involve acidification of the sample and the addition of aluminum nitrate or aluminum chloride salting-out agent prior to isolation of the desired analyte using a tandem combination of prefilter material and extraction chromatographic resin. The method has been applied to the separation of individual analytes from spiked urine samples. Analytes were recovered in high yield and radionuclide purity with separation times as low as 30 min. The chemistry employed is compatible with automation on the ARSIIe instrument.

Influence of the solvent quality on the AhR mediated Procept assay measurement of dioxin and dioxin-like compounds.

Polychlorodibenzo-p-dioxins, polychorodibenzofurans and "dioxin-like" polychlorinated biphenyls are widespread persistent organic pollutants sharing a similar toxicological pathway mediated by the aryl-hydrocarbon receptor (AhR). Since the confirmatory method for their measurement at trace levels in complex matrices (using isotopic dilution and gas chromatography-high resolution mass spectrometry) remains time and cost-consuming, growing efforts of the scientific community have been focused on the development of screening approaches, including AhR mediated assays. Unfortunately, AhR ligands are highly diverse and agonistic/antagonistic effects can be observed on procedural blanks and/or sample extracts. In this study, the influence of solvent grade quality on the response of a DNA-binding AhR mediated assay used for screening dioxins has been investigated. Our results demonstrated a very critical impact of this parameter with both strong agonistic and antagonistic effects observed for any tested solvent lot. A small silver nitrate silica column removed partly these interfering compounds and then can be recommended as final purification step. Some preferable grades can be identified and selected in order to guarantee the best possible performances. However, it appears necessary to test every new lot, even if a grade appeared previously compliant.

Automated two column generator systems for medical radionuclides.

This work describes automated chromatographic methods for the separation of medically useful radionuclides from source material containing their parent radionuclides. The separation techniques employ two chromatographic columns to ensure high chemical and radiochemical purity of the product radionuclide. The separations were performed using an automated system, the automated radionuclide separator (ARS2), consisting of syringe pumps and multiport valves controlled through a computer interface. Generator systems for (68)Ga, (99m)Tc, (188)Re and (213)Bi will be described.

Rapid aryl hydrocarbon receptor based polymerase chain reaction screening assay for polychlorinated dibenzo-p-dioxins and furans in soil and sediment.

A method for the estimation of polychlorinated dibenzo-p-dioxin and furan (PCCD/F) toxicity equivalent quotient (TEQ) of soil and sediment matrices is described. The method includes extraction, isolation of the PCDD/Fs from interfering compounds, such as polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs), and measurement of PCDD/F using the PROCEPT aryl hydrocarbon (AhR) receptor based polymerase chain reaction (PCR) assay. The values obtained using the PROCEPT assay correlate well with reference TEQ values generated from gas chromatography-high resolution mass spectrometry (GC-HRMS), with a linearity coefficient (R(2)) of 0.94. Applied in a screening mode at 50pg/g PCDD/F TEQ, the PROCEPT assay yielded five false positive results (2.6%) and no false negative results for 196 analyses of spiked soils and environmental samples obtained from US EPA Superfund sites.

A method for the separation of beryllium from spectral interfering elements in inductively coupled plasma-atomic emission spectroscopic analysis.

A quick, simple and effective chromatographic method for the separation of beryllium from a wide range of elements is described. The elements selected comprise elements which can interfere with the determination of beryllium by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) and elements which commonly occur in environmental and industrial sample matrices. Beryllium is separated from all possible ICP-AES spectral interfering elements using a single extraction chromatographic (EXC) cartridge containing an acidic chelating organophosphorus extractant, Dipex((R)), sorbed onto an inert polymeric substrate. The separation method has been evaluated using simulated samples generated using several different digestion methods currently employed in beryllium analyses performed in Department of Energy (DOE) facilities. Incorporating a guard cartridge containing either 2-ethyl-1-hexylphosphonic acid mono 2-ethyl-1-hexyl ester or bis(2,4,4-trimethylpentyl)phosphinic acid to selectively remove U(VI) allows the isolation of beryllium from samples containing over 100mg of uranium without changing the load, rinse or strip conditions of the method.